How to Cut Back a Laminate Countertop So I Can Install a Ceramic Backsplash

eHow may earn compensation through affiliate links in this story. Learn more about our affiliate and product review process here.

Things You'll Need

  • 2 sawhorses

  • Preformed laminate countertop

  • Grease pencil

  • Masking tape

  • Heat resistant work gloves

  • Heat gun

  • Safety goggles

  • JIgsaw

  • Fine-tooth carbide blade

  • Medium grit sandpaper

  • Construction adhesive

  • Router

  • Laminate roller

Create room for a ceramic backsplash by removing the preformed backsplash on your countertop.
Image Credit: Jupiterimages/Photos.com/Getty Images

Preformed laminate countertops come with a slight upward rising ridge in the rear; it's a few inches high to serve as a backsplash for your wall. If you'd prefer a ceramic backsplash instead, one that descends to the surface level of the laminate countertop, remove the laminate ridge to make room. Making the necessary cut isn't a difficult process, and it requires no previous carpentry experience. After the removal, you are able to place the ceramic backsplash nearly flush with the countertop, separated from the top of the laminate by only a thin joint.

Advertisement

Step 1

Position a pair of sawhorses on a flat surface wide enough apart to sturdily support the laminate countertop. Set the countertop across the sawhorses, placing it so that the rear of the counter faces upward with the attached backsplash toward you.

Video of the Day

Step 2

Mark a cutting line along the rear of the countertop on the attached backsplash surface with a marker. Position the line so that it runs straight across the length of the counter at the level of the countertop surface. You want to make your cut so that you remove only the upturned portion of the backsplash, not the base, which could shorten the countertop.

Step 3

Place a strip of masking tape over the cutting line, running the full length of the countertop. Turn the countertop over so that it faces upright.

Step 4

Don a pair of work gloves that are rated for use with high temperatures. Turn a heat gun's settings to low. Pass the heat gun over the backsplash of the counter to heat the glue holding the laminate to the counter core, weakening it. Direct the heat back and forth over the countertop, heating the surface evenly. Pull the heated laminate covering from the core of the backsplash section until you reach the base of the laminate backsplash plus an additional inch from the flat, laminated countertop surface. Turn off the heat gun. Flip the countertop back over to access the base.

Advertisement

Step 5

Slip on a pair of safety goggles to wear while cutting the countertop. Attach a fine tooth blade to a jigsaw, and then use the saw to cut through the countertop along your drawn cutting line. Keep the saw going straight along the rear of the counter, removing the upturned section of the backsplash while leaving the laminate that covered the section untouched.

Advertisement

Step 6

Remove the masking tape. Flip the countertop back face upward.

Step 7

Sand the cut surface of the counter smooth and even with the uncut surface you revealed with the inch-long strip of removed laminate. Use medium grit sandpaper for smoothing out the surface, as you want to leave a bit of texture behind for the adhesive. Wipe with a tack cloth.

Advertisement

Step 8

Apply a layer of construction adhesive to the countertop surface as well as to the unattached piece of laminate. Wait for the adhesive to lose its wet look after application. Press the laminate onto the countertop. Roll the laminate smooth with a laminate roller. This will also remove any air trapped beneath the strip. Some laminate covering will overhang the rear of the countertop.

Advertisement

Step 9

Use a router to cut the laminate from the rear of the countertop, cutting it flush to the rear edge. You can install the cut countertop and then place the ceramic backsplash as normal, without the laminate backsplash interfering with the placement.

Advertisement

Video of the Day

references