DIY Bohemian Beach Towel

eHow may earn compensation through affiliate links in this story. Learn more about our affiliate and product review process here.

Summer is in full swing and swimming is #1 on our to-do list. A trip to the beach, lake or pool needs a stylish boho beach towel. These easy and inexpensive towels are sure to make a splash!

Image Credit: Jeran McConnel
Image Credit: Jeran McConnel

Things You'll Need

  • White, 100% cotton towel

  • Rit liquid dye

  • Bucket or large bowl

  • 2 yards fringed cotton trim (I found this at Hobby Lobby)

  • Fray Check

  • Sewing machine with white cotton thread

  • Scissors

  • Large elastic bands

Step 1: Wrap Elastic Bands Around the Towel to Create Patterns

I tested out three different styles and patterns on towels. The pink towel was only dyed on the two ends of the towel. I wrapped four elastic bands about 1½ inches apart (as shown below). I used two to three elastic bands on each stripe and made sure they were very snug. For the single green circle in the center of the towel, I picked the towel up from the very center and then added six elastic bands about 1-inch apart. (Keep reading, I'll have one more design at the end of the post.)

Advertisement

Video of the Day

Image Credit: Jeran McConnel

Step 2: Prepare the Dye

In a bucket or large bowl, mix about 1/3 of a bottle of Rit liquid dye with about 1/2 gallon of hot water.

Image Credit: Jeran McConnel

Step 3: Dip the Towel in the Dye

Image Credit: Jeran McConnel
Image Credit: Jeran McConnel

Tip

Always dye with hot water and rinse with cold water. It will help the dye set. Also adding a couple tablespoons of white vinegar in the rinse water can help keep the colors more vibrant.

Step 4: Rinse Out the Dye

Because I wanted to keep my dye patterns in specific spots on the towels and wanted to keep the rest of the towel crisp white, I was very careful when rinsing the dye out. I ran the dyed portions of the towel under running cold water for quite awhile. When the water started to run clear, I removed the rubber bands (the easiest way is to just cut them with a pair of scissors).

Advertisement

To help set the color, rinse the dyed portions of the towels in a some cold water with a couple tablespoons of white vinegar.

Advertisement

Line dry or put the towels in the dryer.

Image Credit: Jeran McConnel

Step 5: Pin the Trim to the Ends of the Towel

Cut the fringed trim to the length of the towel's widths. Pin the trim to the ends of the towel. Turn the raw edges of the trim under.

Advertisement

Image Credit: Jeran McConnel

Step 6: Sew the Trim to the Towel

Using a sewing machine, sew the trim onto the towel.

Advertisement

Image Credit: Jeran McConnel

Step 7: Prevent the Edges of the Trim From Fraying

Apply a small amount of Fray Check to the edges of the trim. Allow it it to dry completely.

Advertisement

Image Credit: Jeran McConnel
Image Credit: Jeran McConnel

As promised, here's one more dye pattern to try. This grid pattern is really fun, but it's more of an all over dye job and does not leave any white.

Advertisement

Advertisement

Image Credit: Jeran McConnel

Accordion-fold the towel lengthwise and then accordion-fold it again.

Advertisement

Image Credit: Jeran McConnel

Wrap the towel in six elastic bands; three bands in each direction.

Image Credit: Jeran McConnel

Dip all sides of the towel in the dye and then follow the steps from above to rinse.

Image Credit: Jeran McConnel
Image Credit: Jeran McConnel
Image Credit: Jeran McConnel

Advertisement

Video of the Day