How to Make Your Own Silver Bangle Bracelet

eHow may earn compensation through affiliate links in this story. Learn more about our affiliate and product review process here.

Silver bangles add a touch of chic to a casual outfit or a bit of sophistication to more formal clothes, but they can be pricey to purchase. The bangles are less tricky to make at home than you might think, whether you start with jewelry wire or silver sheets.

Silver Sheet Styling

Sterling silver sheets can often be purchased pre-cut to custom sizes.

Advertisement

Video of the Day

Video of the Day

Things You'll Need

  • 14- or 16-gauge sterling silver sheet

  • Jewelers' saw

  • Jewelry file

  • Mandrel

  • Rawhide hammer

  • Jewelry anvil

  • Ball peen hammer (optional)

Step 1

If you did not purchase your sheet cut to size, use the saw to make a silver strip 6 1/2 inches long by the width you want for your bracelet -- usually 1/2 to 1 inch.

Step 2

Use the saw to round the corners on the ends of the strip. This will make your bracelet more comfortable.

Tip

If you prefer, you can cut the bracelet large enough to fit over your hand and solder the ends together to make a continuous-loop bracelet.

Step 3

Use a jewelers' file to smooth all of the edges of the strip, removing the sharp edges. You can finish the last bit of smoothing with an emery board, as well.

Step 4

Use a jewelers' file to smooth all of the edges of the strip, removing the sharp edges. You can finish the last bit of smoothing with an emery board, as well.

Advertisement

Step 5

With the rawhide mallet and anvil, straighten the strip as needed. This also helps to begin the conditioning of the dead-soft metal to make it strong enough to hold up to wearing it.

Step 6

Add texture to your bangle, if you desire, by tapping lightly on the surface of one side of the strip with the ball peen hammer.

Advertisement

Step 7

Bend the strip around the mandrel with the textured side out. Tap the bangle with the rawhide hammer to finish the shaping. Check the fit of your bangle and adjust it as needed.

Wired and Beaded Panache

Make an adjustable, beaded bangle in just a few minutes.

Advertisement

Things You'll Need

  • 14-gauge silver jewelry wire -- 11 inches

  • Needle-nosed pliers

  • Silver beads or charms

  • Side cutters

Step 1

Make a simple loop on one end of the wire. Bend the wire to make a 90-degree angle just above the loop.

Step 2

Slide the beads or charms of your choice onto the wire.

Step 3

Insert the straight end of the wire through the loop at the other end, overlapping the other section of the wire. Make another simple loop around the bottom wire.

Advertisement

Tip

Use your leftover beads to make a stretchy bracelet by stringing them on elastic beading thread. Add them to coated beading wire and use crimp beads to attach a lobster claw clasp and jump ring.

Flattened and Fashionable From Wire

This narrow bangle complements other styles when you stack them together.

Things You'll Need

  • 14-gauge dead-soft silver wire

  • Rawhide hammer

  • Jewelers' anvil

  • Mandrel

  • Jewelry punch (optional)

Step 1

Cut a length of wire about 1 inch shorter than the measurement around your wrist.

Advertisement

Step 2

Place one end of the wire on the anvil and flatten it with the rawhide hammer from the end to about 1 inch up the length. Repeat on the other end.

Tip

You can flatten the entire length of the wire for another variation. After you’ve flattened it, you can also add texture with a ball peen hammer.

Step 3

Add a touch of interest by punching a small hole in each of the flattened ends. If the edges of the hole are rough, smooth them with a metal nail file or emery board.

Step 4

Bend your bracelet around the mandrel and use the rawhide hammer to finish shaping the bracelet.

Advertisement

references